Your bid list for the trades is due before your own bid is, and every package on it carries a decision you will otherwise make by default: bond the sub, trust the sub, or something in between. Making that call one package at a time, with your own payment and performance bonds in mind, costs far less than making it after a sub stops answering the phone.
Bonding every sub vs. screening every sub: choosing the right safeguard for each trade package
A subcontractor bond moves the risk of that sub’s default onto a surety, which has already looked at the sub’s financials. Prequalification leaves the risk with you but gives you information first. Neither is better across the board. Each fits certain packages.
Start with three questions about each package. How large is it compared with your contract? How hard would it be to replace the sub mid-job? How strong are the sub’s financials? A large, critical package such as structural steel, site utilities, or mechanical, where a stalled sub holds up everyone behind it, usually justifies a bond. The premium is a known cost you can price into the bid. If the sub’s balance sheet is thin or its backlog is growing fast, the case for bonding gets stronger.
Small, easily replaced packages such as punch-list carpentry, cleaning, or signage rarely justify the premium or the paperwork. Screening is enough there: recent financial statements, a check of the sub’s credit and lien history, references from other prime contractors, and a look at current workload. Screening works best when you apply it with discipline. If you ask one sub for statements and wave another through because you have used them before, you are not screening anything.
The middle tier is where judgment matters. A mid-sized package with a long-standing, financially solid sub may only need screening. The same package with a newer sub might call for a bond, or for a smaller guarantee such as a letter of credit. Note that bonding does not remove your need to watch the sub. A surety’s backing makes a default recoverable, but it does not make it painless.
Pay-when-paid vs. joint checks and direct payments: setting payment terms that keep the supply chain stable
Standard pay-when-paid terms are easy to administer and push the owner’s payment timing down the chain. They also leave subs and suppliers exposed to delays that are not their fault, and a stressed sub is more likely to slow production or fall behind on its own suppliers. That is where unpaid claims start.
Joint-check and direct-payment arrangements work differently. A joint check names the supplier alongside the sub, so the supplier is paid before the money reaches a sub who may be behind. Direct payment skips the sub for that supplier altogether. These tools suit packages with heavy material cost, a sub with weak credit with its vendors, or a supplier who has begun asking for cash up front. They add administrative work, and they require clear written terms so nobody argues later about what was owed.
Your choice also affects your own exposure. As the prime, your payment bond answers to unpaid subs and suppliers on the project, so a downstream payment failure becomes a claim on your bond, and eventually on your indemnity. Working out how to handle protecting subs and suppliers under a payment bond is easier when your payment terms already reduce the chance of an unpaid bill. For work in Wisconsin and other states with public-works bond requirements, check how notice and claim deadlines apply before you draft terms, since the rules affect how quickly an unpaid supplier can reach your bond.
Self-insured risk vs. transferred risk: matching your protection to your balance sheet and your bonded exposure
Even with bonds and screening in place, some packages leave residual risk. You can absorb it or transfer it. A default insurance program transfers it, reimbursing certain costs when a sub fails, usually with a deductible and a limit on covered losses. Self-insuring means you hold the exposure yourself and cover any failure from working capital.
The deciding factor is your balance sheet, not your confidence. One failed major sub can cost a lot in completion expense, delay damages, and disrupted schedule. If a single loss of that size would strain your working capital, or limit the capacity your surety is willing to give you, transfer the risk. If your capital is deep and your trade base is diversified, self-insuring the smaller packages is defensible. Many primes combine the two, transferring risk on the top few packages and absorbing it elsewhere.
Before bids go out, complete this for every trade package:
1. Package value as a share of your contract. 2. Criticality: how many other trades depend on it, and how long would a replacement take? 3. Sub financial strength: strong, adequate, or thin, based on current statements. 4. Safeguard: bond, screening only, or a bond alternative. 5. Payment terms: pay-when-paid, joint check, or direct payment to named suppliers. 6. Residual risk: insured, self-insured, or already covered by the sub’s bond. 7. Cost added to the bid for every choice above.
Once the worksheet is filled out, the decision in front of you is whether the roster as a whole fits your balance sheet and your payment bond obligations. If the packages you left unprotected could, together, hurt more than you can afford, change them now, while the bid is still open.